fokiwed.blogg.se - Osculator wiimote tutorial

#Osculator wiimote tutorial how to
#Osculator wiimote tutorial mac os
#Osculator wiimote tutorial Pc
#Osculator wiimote tutorial Bluetooth

Immediately click the "Start Pairing" button in the Wii Remote Setup Panel in OSCulator.Newer models have a small hole that allows you to use a paperclip or pin to press the button without removing the cover. On older Wii Remotes, you will need to remove the battery cover to access this button. To make the Wiimote available for pairing, you must press the little red button inside the battery compartment.Click the icon to reveal the Wii Remote Setup Panel. At the top right is an icon labeled WiiMote.To pair OSCulator and the Wiimote, follow these steps (To do this, go to the System Preferences, click on "Bluetooth" and ensure that the top checkbox labeled "On" is checked.)īefore OSCulator can send the WiiMote data to Isadora, it must be "paired" with the WiiMote.

#Osculator wiimote tutorial Bluetooth

OSCulator is robust, reliable, allows you to use multiple WiiMotes at the same time, and is relatively inexpensive.Īfter downloading and installing OSCulator, you will need to set up an OSCulator document that will allow Isadora to "listen" to the data from the Wii Remote.īefore running OSCulator, make sure that the Bluetooth port on your computer is enabled.

#Osculator wiimote tutorial mac os

We strongly recommend the software OSCulator to accomplish this task on Mac OS X. Instead, you must use an intermediary piece of software that will read the data from the Wiimote, and pass it on to Isadora in a form it can understand. Isadora cannot read the signal from the Wii Remote directly.

#Osculator wiimote tutorial how to

Below you will find step-by-step instructions on how to get Isadora and the Wii Remote (or Wiimote as it is often called) to work together. This entry was posted in Uncategorized on Maby Mike O'Connor.The Nintendo Wii Remote is a wireless sensory device that can be used in conjunction with Isadora to sense movement or to trigger actions using one of its eleven buttons.

Cranking up the “Smoothing” settings in the 1st instance of OSCulator fixed that.

Signals coming into Live were quite jittery at first.

So the control wouldn’t “pick up” the MIDI signal. It turned out that sometimes controls were set to a higher value than the maximum value coming to them from OSCulator.

I found that controls sometimes wouldn’t work.

I found it useful to turn all the devices off (untick the boxes in the left column) before starting the mapping. The mappings will appear in the box on the left (under “MIDI Mappings”) as they’re added. Turn on the MIDI Map Mode switch (blue, in the upper right corner, says “MIDI”), click on the control that should receive the MIDI signals and toggle the device on and off in OSCulator. Once OSCulator is producing MIDI, Ableton Live can be trained to apply those MIDI signals in the normal way. I picked those message numbers because they’re within a range (85-90) that’s generally not used by other devices. OSCulator has been configured to convert the OSC messages from Wekinator to MIDI CC messages in this example. If Wekinator is running, OSCulator will pick up the Wekinator outputs and they should be displayed in the Messages column of OSCulator.Ģnd instance of OSCulator to Ableton Live The second instance of OSCulator (instantiated through File/New) is set to listen on port 12000. The default Wekinator output port is 12000. Wekinator to OSCulator (this is the second instance of OSCulator) If Wekinator is running, locating and selecting these entries should be available through the drop down menus. If you are starting from an empty OSCulator file, here is what the Parameters page looks like in this first instance of OSCulator. I’ve included the mapping if you are building this from an empty OSCulator file. This first instance of OSCulator translates the motions of the WiiMote into OSC messages and pushes them to Wekinator on Wekinator’s default UDP port (6448). Here’s the way it looks when it’s working.

Open the sliding panel on the right side of the main OSCulator page, turn on the WiiMote, click “Start Pairing”. Open OSCulator with the 3-input template linked above. WiiMote to OSCulator is a built in feature of OSCulator. oscd templates to simplify the connection from OSCulator to Wekinator. Here is a block diagram (clicking on it makes it bigger) Wekinator outputs are mapped to MIDI to drive Ableton Live through another instance of OSCulator. In this configuration a WiiMote (input device) is connected to Wekinator (real time interactive machine-learning software) through OSCulator (OSC bridging and routing software).

#Osculator wiimote tutorial Pc

This won’t work on a PC as some of the software is Mac-only. This is a scratchpad post to remind myself how to put together a machine-learning system on a Mac.